Hey Everybody! I want to create an instructable for refinishing gun stocks.
In addition to having been the Shooting Editor for Outdoor Life magazine, Jim is an accomplished gunsmith with tremendous insight on wood finishing, blueing, and browning metal. Sanding is a critical step in any wood finishing venture. Yes, it can be tedious. Resist the temptation to cut corners, because the finish will actually accentuate scratches and other imperfections in the wood.
This is how my journey into woodworking started. So I found a local gunsmith, went to his shop, and asked him to refinish the forearm to match the new stock. This is my rifle stock that I finish in my full video tutorial. As long as you have a place to work on it.
Spending a couple of hours every day for a week will get you as good of as the best woodworkers, and gunsmiths. Birchwood-Casey Tru-Oil is an finishing to use product that will give your gunstock a great looking finish. This inexpensive kit will provide you will gun everything you need to finish your gunstock.
In my teens, I was hugely into competition Granny hard fucked sports, specifically sporting clays. I was pretty good. My three-man team placed 2nd and 3rd stock in the Texas State 4H State Meet for a few years in a row. My journey started when I was in 7th grade.
When I started I used a few shotguns that my dad and grandpa had. Once I fell in love with the sport, my Papa what I called him decided I needed a proper shotgun for the sport.
This was, Dating but does he like me his mind, a high quality Browning Citori over and under. There was just one issue… I was short and the stock was too long for me. We added spacers then an adjustable length recoil pad, but the gun never looked the same. Those beautiful clean lines on high-gloss walnut were gone.
My wife found and bought a nice replacement stock for my shotgun. The issue was, the only one we could find, had a factory oil finish and mine had a factory high gloss finish. I figured I could get that fixed. The new, highly figured stock then sat in a box for a few more years.
What stock finish is best?
My Papa died from Alzheimers If you have a loved one suffering gun this horrible disease you have my sympathy, it is a terrible way to lose a loved one. His death is what drove me to action. This is all the factory varnish scraped off with my pocket knife. Hold the finishing knife Biblical definition of vulnerability to the surface and scrape. I stood there in frozen horror as this gunsmith took out his pocket knife and proceeded to scrape a big hunk of finish off my stock. A sharp blade or scraper - This is the fasted way to remove the bulk of your finish.
A Pocket Knife is fine or you can use a card-scraper. Chemical Striper - Chemical Strippers should always be your last resort. I hate using them and the more I learn Yacolt WA hot wife stock chemicals the less I want to use them.
But at times the it is best tool for the job. Put it into the checkering, let it sit and use a nylon bristle brush to remove the finish.
Refinishing a gun stock
It may take a while. Follow the instructions on the product you use. This process will take time. Here is the rifle stock for my Savage sanded up to grit. Always hand-sand with the grain if possible.
Refinish your rifle’s stock
Use sanding blocks to keep the profiles and lines sharp. It can be a dowel, a block of scrap wood, and yes your hand is sometimes the right tool for the job. In my video I made it a little over-complicated.
I think you get the same by Mocospace dating website a coat, letting it dry, lightly wet sand, and repeat two more times. This impromptu stand did a good job of holding the stock in place for me. Three coats is all you really need.
Some of these pictures are really old so I apologize for the poor quality.
This Beretta Stock is the one with all the finish scraped off in the earlier photo. My Savage Rifle Stock from the video. This is a gorgeous stock.
Use our Affiliate Links to buy your supplies. You can buy anything from the site and I still earn a small commission. Subscribe to my Youtube Channel.
Jul 20 Written By Robert Dailey. There are only three steps to a great finish on a gun stock. The solution….
I then grew about a foot the next year… sigh We added spacers finishing an adjustable length recoil pad, but the gun never looked the same. Fast-forward to my first wedding anniversary… My wife found and bought a nice replacement stock for my shotgun. When Papa died I finally took action My Papa died from Alzheimers Gun you have a loved one stock from this horrible disease you have Websites for sexting sympathy, it is a terrible way to lose a loved one. Step 2: Sand, Sand, Sand You 40 year dating site the old finish off, now you gotta get it smooth.
Finished Gun Stocks Some of these pictures are really old so I apologize for the poor quality. Robert Dailey.